Showing results: 451 - 465 of 473 items found.
-
Analog Devices Inc.
Recognized as the pioneer and leader in RF detectors, Analog Devices offers a broad portfolio of high performance logarithmic amplifiers and TruPwr™ rms responding detectors. ADI logarithmic amplifiers measure signals up to 100 dB dynamic range, from dc to microwave, and accuracies of ±0.2 dB, and are well-suited for both RSSI and transmit power level detection. The TruPwr rms detectors address the challenge of measuring complex waveforms found in spread spectrum CDMA/W-CDMA and higher order QAM modulation systems and provide an accurately scaled dc voltage, which is the rms equivalent of the input waveform.
-
Keysight Technologies
Keysight's PXI arbitrary waveform generator (AWG) deliver unprecedented performance for creation of complex wideband waveforms. High sampling rate and high bit resolution provided in a single instrument enable designers to create ideal waveforms for accurate test of radar, satellite and frequency agile systems. Providing up to 500 MHz of modulation bandwidths and over 65 dBc of spurious free dynamic range, PXI arbitrary waveform generators can be combined with a wideband I/Q upconverter to achieve modulation bandwidth of 1 GHz at microwave frequencies for realistic signal simulations for IF and RF subsystem test.
-
3024 -
LBA Group, Inc
The COMM-connect 3024 RF Power Monitor from LBA Technology can control up to 8 external RF Measuring heads. The high dynamic range with external couplers and RF measuring heads cover from 1W to 1MW. The Power conversion algorithms handles multi carrier, multi mode, peak, average and RMS signals. The power readout is auto scaled and VSWR can be calculated between any probes. Also the measured and calculated results along with alarms can be shown in the local LCD. The instrument has SNMP support to allow network management. The instrument can be configured for VSWR and Power limits to give alarms. The alarms can be configured to operate relay drivers or isolated Optcouplers. The alarms can also be configured as SNMP traps sending relevant information to the network control center. The COMM-connect 3024 WEB enabled RF Power Monitor gives an unlimited number of applications to monitor and control the last part of your RF network installation from transmitters to the antenna.
-
6330A series -
Chroma ATE Inc.
The 6330A family offers 8 types of modular loads with power ranging from 30 watts to 1200 watts, current from 0.5mA to 240A, and voltage measurement from 0.5mV to 500V. Each load is isolated and floating, programmable in dual current range and measuring voltage range, and capable of synchronizing with other modules for control operating. The load can be operated in constant current, constant voltage, and constant resistance. With Synchronic parallel control capability, 6330A series loads allow users to parallel and synchronize more than one load together from an internal loading control signal. This feature provides synchronic dynamic loading test for multi-output power and high power test solution. Real time measurement of voltage, current, is integrated into each 6330A load module using a 16-bit precision measurement circuit. The user can perform on line voltage measurement and adjustment, or simulate short circuit test using the simple keypad on the front panel.
-
SEN-36002 -
Playing With Fusion Inc
SEN-36002 is a highly integrated carrier board designed for the Si1145 UV, Ambient Light and Proximity sensor IC from Silicon Labs. This sensor has 100mLUX resolution, and has a dynamic range of 1 LUX to 128 kLUX with IR correction. This means that whether your application is indoors in poor lighting conditions or outside in full sunlight, this sensor has you covered. In addition, we added a high power LED (150mA max, 20 degree) to take full advantage of the proximity sensing capability of this IC - something you won't see on most competitive carrier boards. Integration is easy with 4 x 4-40 sized mounting holes at the corners of the PCB and signal translation to handle interface voltages from 3V to 5V. The board is interfaced via an I2C interface and function pins have been broken out to a 0.1" pin header. The INT pin is also broken out for interrupt capability.
-
XYL-VI -
Lisun Electronics Inc.
The XYL-VI Luminance Photoelectric Colorimeter changes the traditional structure thoroughly, employs the digital X(λ), Y(λ), Z(λ) sensors to replace the traditional analogue sensors, employs the digital signal measurement system to replace the traditional analogue measurement system. The instrument has no analogue unit, thus it is very simple to overcome the zero drift that is impossible to be avoided in traditional colorimeter. The digital sensor has a large dynamic range. Moreover, it possesses strong anti-interference ability and it has high accuracy. The XYL-VI Luminance Colorimeter contains internal RS232 computer interface. The calibration is done by software. It is suitable for monitoring and remote applications. The XYL-VI Luminance Colorimeter can be calibrated by XYL-VI Luminance Colorimeter software to sample the data and print out the results. It can also be corrected by other standard light sources to obtain very high measuring accuracy of x, y color coordinates and color temperature. It is a real-time measuring system and run under Windows2000/XP.
-
J2110A -
PICOTEST Corp.
While it is possible to obtain high quality injection transformers with bandwidths as wide as 1Hz to 5MHz or more, in some cases this is still insufficient for some tests. For example a typical heater control loop might have a bandwidth of less than 1Hz while some linear regulators and opamp circuits can have bandwidths of up to 100MHz or in some cases even higher. For these applications, a solid state injector can provide the necessary bandwidth. A solid state injector can perform at DC, while the upper frequency limit is dictated by the components selected and the printed circuit board material and layout. It is possible to obtain a solid state injector with a working range of DC – 200MHz, though above 50MHz the interconnection between the injector and the circuit being tested can become quite critical. It is essential that ripple from the injector power supply does not dramatically degrade the dynamic range or the signal to noise ratio of the measurement. The resulting plots are often much cleaner when using a solid state injector than with a transformer injector.
-
P55 -
Validyne Engineering
The robust P55 pressure transducer provides cost-effective reliability for severe test environments. With extreme resistance to shock and vibration, the P55 pressure transducer delivers the same high-level performance expected from more delicate differential pressure transducers and pressure transmitters. With variable reluctance sensing technology, the P55 pressure transducer delivers fast dynamic response, high resistance to vibration and superior signal stability through ambient temperature change for a wide variety of low-pressure to high-pressure measurements. The P55 pressure transducer will accept both liquids and gases directly at the sensing diaphragm and there are no internal isolation fluids to slow the sensor response or cause excessive temperature drift errors.
-
PXIe-9848 -
ADLINK Technology Inc.
The ADLINK PXIe-9848/9848H is an 8-channel, 14-bit, 100 MS/s digitizer delivering both high-accuracy measurement results and high-dynamic performance. With a PXI Express bus interface and ample onboard acquisition memory up to 512 MB, the PXIe-9848/9848H can easily manage simultaneous 8-CH data streaming. High density and high speed digitizer features ideally position the PXIe-9848/9848H for applications such as LIDAR, radar signal acquisition, and PSU (Power Supply Unit) testing applications.The PXIe-9848 provides a flexible set of input ranges from ±0.2V to ±2V, software selectable 50Ω or 1MΩ input impedance, a wide variety of triggering options and tight synchronization capability, all maximizing convenience of use. In addition, ADLINK provides the PXIe-9848H, features a x15/x50 signal condition module providing both high input voltage range of ±100V and high dynamic performance, delivering the optimum solution to measurement range expansion in a PXI system.
-
Fideris
* Fully programmable, self-contained, air-cooled solid state load.* Patented design is optimized to provide ultra-low impedance operation for fuel cell testing.* Load is compatible with AC impedance or frequency response analyzers.* Interchangeable shunts for precise operation over a wide dynamic range.* Ten built-in cell voltage monitoring inputs optional. Additional voltage monitoring inputs available.* Ethernet Interface for simple configuration and expansion!* Combine with additional Fideris™ Innovator Series™ modules to create a fully-integrated,fully-automated, customized test system.* System-wide control of all Fideris™ Test System Components using FCPower™ Software,LabviewTM, or other programming language.* Integrated hardwired Run/Standby signal.
-
LXinstruments GmbH
Among other things, solar array simulators are required for testing satellite power supplies. An SAS (Solar Array Simulator), consisting of an interconnection of several Solar Array Simulator modules, maps the solar panels and displays the individual strings connected in parallel. Optionally, the individual SAS modules are monitored by a Second Level Protection, so that the test object is not damaged in case of errors with the voltage sources. Additional circuitry is implemented via project-specific test modules. The signal path to the DUT can be separated, e.g. for dynamic current measurements.The Keysight Solar Array Simulators used were specially developed for satellite applications and cover the significantly higher requirements regarding the control speed of MPP tracking compared to terrestrial applications.
-
X1-1-RCH-116-4 -
Gigahertz-Optik GmbH
The X1-1 radiometer from Gigahertz-Optik features an RCH-116-4 detector and is ideal for measurement of the irradiance of high power LEDs in the UV-A and blue light range. The device can accurately measure irradiance levels of up to 40,000 mW/cm². One of the outstanding features of the RCH-116-4 detector is its proven concept of a passive radiation absorber coupled to a UV sensor. This provides stability even in high temperature and intense UV radiation environments. In addition to the passive radiation absorber, the device also has a cosine-corrected field of view. The sensor’s housing also serves as a handle. The battery-powered X1-1 optometer supports a usable dynamic range from less than 1 mW/cm² to 40,000 mW/cm² thanks to its high-end signal amplifier. It can be used to perform precise measurements of up to 5 standard LED wavelengths for which the detector was calibrated for active irradiance. In addition to the CW measurement function, the device also has a dose measurement function. The radiometer can be used with other detectors from the RCH series. e.g. for gas discharge lamps. Remote control of the device is possible via its user software and a software development kit is offered for integration of the device in the user’s own software.
-
Model 5585 -
Pentek, Inc.
- Jade 5585 and 5586 FAQ- Complete radar and software radio interface- Wideband data acquisition- Multi-channel, multi-board synchronization for high channel count systems- High-bandwidth memory, FPGA logic and DSP density make this board a single-slot 3U VPX processing powerhouse- Exceptional dynamic range and analog signal integrity- Features Xilinx Virtex UltraScale+ HBM FPGAs- Eight 250MHz 16-bit A/Ds- 10 GigE Interface- 40 GigE Interface- Dual 100 GigE UDP interface- Optional VITA 67.3C optical interface for backplane gigabit serial communication- Compatible with several VITA standards including: VITA 46, VITA 48.11, VITA 67.3C and VITA 65 (OpenVPX™ System Specification)- Navigation Design Suite for software and custom IP development
-
NFO series -
Radiantech, Inc.
The NFO OTDR unit injects the laser pulse into the fiber under test and picks up scattered and reflected optical signals by an avalanche photodiode (APD). The unit accepts remote commands from Internet to control all related timing and data acquisition processes. Maximal three wavelengths are available at the NFO with options on 1310, 1490, 1550, and 1625 nm. NFO also has options on dynamic ranges so users can select the most cost effective units for their demands. Radiantech provides an easy use API (Application Program Interface) for NFO so users can design and build their own AP for NFO. Standard NFO API package is for Windows XP or higher. Please contact Radiantech’s sales person to inquire API for another OS.
-
784277-01 -
NI
1.25 MS/s, 3.4 Hz AC/DC-Coupled, 6-Input PXI Sound and Vibration Module—The PXIe‑4480 is designed for high-bandwidth audio, acoustic, and vibration measurements. It provides six channels of dynamic signal acquisition, and you can use one of four gain settings to configure your input range. The PXIe‑4480 also includes software-configurable AC/DC coupling, charge measurement, voltage excitation, IEPE excitation, and TEDS support, making it ideal for measuring acoustic transducers, pressure sensors, and hydrophones. Common applications include audio test; noise, vibration, and harshness (NVH) analysis; and underwater acoustic measurements. For measuring sudden changes, such as high speed blast and pressure events, the PXIe-4480 can sample up to 20 MS/s per channel in time-domain mode.
